3M CAST VINYL ROLLS
- Adhesive vinyl roll
- Sold in 48" tall x 12" wide increments continuous roll
- 3M cast vinyl with lamination
- LIMITED LIFETIME WARRANTY
- Sold in 12" increments: 48" x 12" section = 4 sq. ft. of material
|BEFORE CAMOUFLAGE INSTALLATION:|| The First Step in any installation is the proper cleaning of the Camowraps® Project. All project surfaces must be thoroughly cleaned before applying your vinyl graphics. Since all surfaces are different, follow the cleaning instructions below for your specific material’s cleaning procedure.
Plastics and Glass
Thoroughly wipe surface clean with a window cleaner. Remove any dried matter such as tape or glue with a single edge razor blade. If you are planning to use acrylic, remove the protective liner from the acrylic 24 hours prior to application vinyl graphic. This will allow any air bubbles (out-gassing) to dissipate from the acrylic. If this is not observed you may find air bubbles form under your graphic within a couple of days.
Painted Metals and Base Metals
These surfaces may be cleaned with a solvent such as Naphtha, Xylol or Lacquer Thinner. Dry the surface with a lint free cloth before the solvent evaporates. The most effective method of completing the cleaning process is the two hand, two cloth method: Using two cloths (one dry, one with Solvent) one in each hand, wipe the solvent on with the wet towel and then quickly wipe off with the dry one. This is to keep the solvent from drying onto the surface. CAUTION: Before Using any Solvent on a Painted surface, be sure to test in an inconspicuous area to ensure the solvent won’t damage the paint. Freshly painted surfaces should be dry for at least 72 hours prior to application of the vinyl graphics.
Interior Painted Surfaces
Surfaces may be cleaned with any household cleaner such as Fantastic or 409. Wipe area clean and dry with a lint free cloth before applying the vinyl graphics. Freshly painted surfaces should be dry for at least 72 hours prior to application of the vinyl graphics.
|RECOMMENDED INSTALLATION CONDITIONS:|| Whenever possible, try to apply graphics indoors in a controlled environment, such as a covered car bay or garage. Doing so will not only help you control the temperature (ideally between 70°F and 80°F), but also reduce the amount of wind, dust and other contaminates that may hinder the install process. Make sure your bay or garage is as clean as possible from dust or debris that may happen to circulate during your install (mop floor and dust with a damp cloth) before bringing in the surface for the vinyl application.
If you must do your install outside, grab a friend and choose a non-windy day that is between 60°F and 90°F, with a surface temperature over 45°F (use water to cool surface) to insure the adhesive bond forms correctly.
|HOW TO INSTALL
There are 2 basic ways to install your Camowraps® Vinyl; the first is the “Peel & Stick” Method and the second is the “Hinged” Method. Depending on the Size of material you are working with, the method you use will change. Follow the steps below for both methods. If you need additional information visit Camowraps.com for more.
“Peel & Stick” Method (recommended only when working with small areas)
Complete by cutting your material to the required size and then simply peeling the entire backing off the vinyl and sticking the vinyl piece down and start squeegeeing. This technique is not recommended for everyone.
“Hinged” Method (recommended for larger or continuous pieces that overlap) See Diagrams for more info...
|CAMOUFLAGE CARE TIPS:||Use soap and water to clean graphics. Do Not use a pressure washer on graphics as this can cause them to rip and peel away. Do Not wax the graphics; it will only cause damage to them.|
|HOW TO REMOVE:||
Camowraps is committed to providing quality products that are sure to surpass expectations. However, if you are unsatisfied with your purchase, you can exchange or return your undamaged, uninstalled graphic within 90 days of delivery. After 30 days of delivery, products will be subject to a restocking fee.
To obtain your refund/exchange, please contact our customer service department at 1-866-226-6626. Return items should be in their original packaging, include all packing materials and receipt.
Defected or Damaged Product Returns:
If you received an item containing defects, please contact customer service at 1-866-226-6626.
We can ship to virtually any address in the world. Note that there are restrictions on some products, and some products cannot be shipped to international destinations.
When you place an order, we will estimate shipping and delivery dates for you based on the availability of your items and the shipping options you choose. Depending on the shipping provider you choose, shipping date estimates may appear on the shipping quotes page.